Specifications
1, quartzware
2, tight tolearance
3, Resistance 1100 degree
4, no bubble no airline
5. ISO 9001-2000
Customisized solution quartzware
1, quartzware
2, tight siz tolearance
3, Resistance 1100 degree, 2020 f
4, no bubble no airline
Advantage of the quartz tube:
1. High temperature resistant, 1100 degree.
2. Corrosion-resistant
3. Good thermal stability
4. Good transparency for light
5. Good electrical insulation
1, quartzware
2, tight tolearance
3, Resistance 1100 degree
4, no bubble no airline
5. ISO 9001-2000
Customisized solution quartzware
1, quartzware
2, tight siz tolearance
3, Resistance 1100 degree, 2020 f
4, no bubble no airline
Advantage of the quartz tube:
1. High temperature resistant, 1100 degree.
2. Corrosion-resistant
3. Good thermal stability
4. Good transparency for light
5. Good electrical insulation
Range of OD | OD | WT | Siding | Out of Rou n d | Bow\1220mm |
≤6mm | ±2.0% | ±10% | 12% | 2.0% | 2.5mm |
6.00-15.00mm | ±1.25% | ±8% | 10% | 1.5% | 2.5mm |
15.00-20.00mm | ±1.25% | ±10% | 15% | 1.5% | 2.5mm |
20.00-25.00mm | ±1.25% | ±10% | 15% | 1.5% | 3.0mm |
25.00-30.00mm | ±1.35% | ±12% | 15% | 1.5% | 3.0mm |
30.00-80.00mm | ±1.5% | ±14% | 15% | 2.0% | 3.0mm |
80.00-100.00mm | ±1.0% | ±0.5mm | 15% | 2.0% | 3.0mm |
100.00-120.00 | ±1.5% | ±0.8mm | 15% | 2.0% | 3.0mm |
120.00-160.00 | ±1.8% | ±1.0mm | 20% | 2.5% | 3.0mm |
160.00-180.00 | ±3.0% | ±1.0mm | 25% | 2.5% | 3.0mm |
180.00-200.00 | ±4.0% | ±1.5mm | 25% | 2.5% | 3.0mm |
200.00-240.00 | ±4.0% | ±1.5mm | 25% | 2.5% | 3.0mm |
240.00-280.00 | ±6.0% | ±2.0mm | 25% | 2.5% | 3.0mm |
280.00 above | ±8.0% | ±3.0mm | 25% | 2.5% | 3.0mm |
C hemical composition (ppm)
AL | Fe | K | Na | Li | Ca | Mg | Cu | Mn | Cr | B | Ti |
5-12 | 0.19-1.5 | 0.71-1.6 | 0.12-1.76 | 0.38-0.76 | 0.17-1.23 | 0.05-0.5 | 0.05 | 0.05 | <0.05 | <0.1 | <1.0 |
S pectral transmission at 1.0mm thickness
m m | <220 | 255 | 280 | 315 | 350 | 38 | 590 | 780 |
% | 89 | 91 | 93 | 93 | 93 | 93 | 93.2 | 93.4 |
Physical Prop er ties
(g/cc)Density20 °C kg.m-3 | 2.2 |
Degree of Hardness Moh's Scale | 5.5-5.6 |
Softening point(degree) | 1683 |
Annealing point | 1215 |
Defoamation Point | 1120 |